The Harris Products Group / Guides
Oxy-Fuel and Air-Fuel Basics
Oxy-fuel versus air-fuel
An oxy-fuel torch burns a fuel gas with pure oxygen from a second cylinder. The flame is hot enough to cut steel, heat heavy parts, gas weld and braze. An air-fuel torch burns fuel with air from the room, so it needs only one cylinder and has a cooler flame. Harris describes its air-fuel hand torches as portable, suited to field installation and repair and good in confined spaces, which is why HVAC, plumbing and refrigeration techs use them for brazing and soldering copper. Cutting steel is an oxy-fuel job.
Fuel gases
- Acetylene has the hottest, most concentrated flame. Harris says it is preferred for thin plate (3/16 in. or less), piercing, beveling, rounded edges and flame hardening, and that gas welding can only be done satisfactorily with acetylene. For safety, acetylene is limited to 15 psig; never set it higher.
- Propane, natural gas and propylene are called alternate fuels. They burn slower, and Harris says they generally have a higher BTU value per volume, are safer, flash back less often and leave cleaner cut edges. They suit thick plate and heating.
- Map-Pro® gas, propylene and MAPP. Harris lists Map-Pro® gas with its propylene cutting tips (6290-NXP) and its air-fuel hand torches, which are listed for Map-Pro® gas or propane. On the Fastenal list, Inferno® HA tips are air-fuel/acetylene and HT tips are air-fuel/propane/MAPP. Check the tip or torch for the gases it accepts.
Acetylene cylinders hold acetone. Drawing gas too fast pulls acetone out and is unsafe. Harris cites the "1/7 rule", which CGA G-1 has since reduced to 1/10 of the cylinder contents per hour. Heavy heating tips can need more than that, so Harris recommends alternate fuels for big heating jobs.
Cutting, heating, welding and brazing
Harris says cut quality depends on tip size for the steel thickness, preheat flame setting, cutting oxygen pressure, travel speed and tip condition. Heating uses the 2290-H heavy-duty heating tips (alternate fuels) or J-63 acetylene rosebud tips. Welding and brazing use smaller tips such as the 23A90, 5090 and 1390 families. Harris separates gas welding, which melts the base metal and uses acetylene, from braze welding, which melts only the filler, can use other fuels and needs flux. Oxy-fuel rod RG45 and RG60 are for gas welding steel and need no flux.
Shutdown order: Harris recommends closing oxygen first on acetylene. With alternate fuels, after the first lighting, it recommends fuel first. Remember that a check valve does not stop a flashback; it stops reverse flow. A flashback arrestor is a separate device.
How Harris tip numbers read
The model number (6290, 23A90, 1390) names the tip series. The Harris catalog and product pages say what each series is for:
- 6290: one-piece general-preheat hand cutting tip for acetylene.
- 6290-S: one-piece heavy-preheat acetylene tip for painted, rusted or heavily scaled steel. Sizes read 1S, 2S, 3S.
- 6290-AC: two-piece heavy-preheat acetylene tip, also recommended for acetylene machine cutting. Sizes read 00AC, 0AC, 1AC.
- 6290-N and 6290-NX: two-piece, general preheat, propane and natural gas. Sizes read 0NX, 1NX, 2NX.
- 6290-NFF: two-piece, heavy preheat, propane and natural gas.
- 6290-NXP: two-piece, general preheat, propylene and Map-Pro®.
- 6290-NH, 6290-VVC, 6290-VVCU and 6290-VVCP: two-piece machine tips. VVC is for propane and natural gas, VVCP for propylene, and VVCU is the "economical" high-speed version.
- 23A90, 1390 and 5090: one-piece or separable welding, brazing and heating tips for acetylene; the -N versions are for propane and natural gas.
The dash number on a Fastenal item, such as 6290 -4 NX, is the tip size. On the catalog's cutting tip charts, size follows the cutting oxygen hole in drill sizes. For the 6290 acetylene tip, size 0 cuts 3/8 to 5/8 in. steel (drill no. 60), size 2 cuts 1 to 2 in. (no. 52) and size 4 cuts 3 to 6 in. (no. 42). Harris says there is no industry standard for tip sizes, so compare tips by chart, not by number. The catalog does not define the M suffix (for example 6290 -5 NXM or VVCM), so confirm it on the item page. "Harris Style" in a Fastenal name means the tip is made to fit Harris torches.
How Harris regulator model numbers read
The Harris catalog lists every regulator as model, delivery range, then CGA inlet:
- 25GX-15-510: Model 25GX single-stage regulator, 0-15 psi delivery, CGA 510 inlet. The catalog lists it for acetylene. The 25GX-50-510P is the propane (LPG) version.
- 9296SS-50-320: Model 9296SS, a two-stage regulator with a stainless steel diaphragm, 0-50 psi delivery, CGA 320 (carbon dioxide).
- 447-50-1/4"R and 547-50-CL: Pipeline and station regulators. The inlet code follows the range. In the catalog, "1/4" means a 1/4 in. NPT inlet. "C" means the station "C" inlet (limited to 200 psig). L and R mean left-hand (fuel) or right-hand (oxygen and others) threads.
- 301-80-IGGRF-032: Model 301 inert gas guard with flowgauge. Here 80 is the 0-80 SCFH flow range, not a pressure. Harris does not explain the 032 suffix.
Harris says to pick a delivery range so the working pressure falls in the middle two-thirds of the range. "NC" in a model (for example 9200NC-15) marks the low-pressure versions with a neoprene seat. "A" in a Fastenal name (601-15-520 "A") is the hose fitting size, and LH and RH mean left- or right-hand thread.
Stock number versus model number
Harris product pages show a 7-digit stock number under the model name. For example, Model 301-80-IGGRF-032 has stock number 3000328. Fastenal's short descriptions often start with that number, and the long description holds the model. Both identify the same part.